Category: ∨g=maxi-aids-inc

DIY Seat For a Walker

AbleData does not produce, distribute or sell any of the products listed on this website, but we provide you with information on how to contact manufacturers or distributors of these products. If you are interested in purchasing a product, you can find companies who sell it below.

DIY Seat for a Walker is designed for use by individuals who have walking disabilities and use a walker for mobility. It is designed to provide a seat to rest during ambulation.

Technical Specifications: 
  • Step 1: Gather tools and materials Sewing machine Scissors Seam ripper (not pictured) Lighter Materials Length of car seat harness webbing 1-inch flat nylon webbing Heavy duty upholstry thread 4-1 inch welded steel D rings 8-1 inch welded steel O rings 4 -3/4 inch electrical conduit claps (dipped in plastic dip prior to use) To attach to walker I used Pliers flat headed screwdriver
  • Step 2: Decisions of size Decide how large you want the seat portion.
  • Step 3: Cutting side lengths Cut 2 lengths of the wider webbing into 13.5 inches pieces. Flash in a lighter flame to melt ends to prevent fraying. Fold over ends and make the loops a tiny bit wider then the webbing itself. You will need to pass the O rings through the loops. Stitch back and forth 4-5 times. Repeat on each end. You should end up with 2 straps with loops on each end.
  • Step 4: More cutting Cut another 2 lengths of the wider webbing. Melt ends to prevent fraying. I chose 16 inches lengths. Insert the lengths into the looped ends and sew together using a straight stitch with machine. Sew only on outside edge and go forward and reverse 4-5 times.
  • Step 5: Cutting supports Cut 3 lengths of wider webbing into desired sizes. I chose 15.75 inches. Melt ends to prevent fraying. Attach each piece to the underside of the frame, spacing each evenly. Use a straight stitch and go forward and reverse 4-5 times. Repeat on the other side.
  • Step 6: Cutting more supports Cut 7 lengths from the wider webbing in 8.5 inches lengths. Melt ends to prevent fraying. Attach onto frame underside on the longer side using straight stitch and going forward and reverse 4-5 times.
  • Step 7: Weaving Weave the webbing through the longer supports alternating each. Sew using a straight stitch on opposite side. Repeat with all straps. Be sure to stitch forward and reverse 4-5 times.
  • Step 8: Reinforcement Reinforce all intersections using a straight stitch. Take care to not stitch the looped ends closed. The seat is mostly completed. Set aside.
  • Step 9: Cutting thinner webbing Measure and cut 4 lengths of the 1-inch nylon webbing into desired lengths. Be generous with the lengths. The author measured and cut their pieces into 4 feet pieces. Next, melt ends to prevent fraying. Sew 2 lengths together and fold over ends.
  • Step 10: Cutting more thinner webbing Cut 2 lengths of 1inch nylon webbing into desired lengths. I cut mine at 24 inch. Melt ends to prevent fraying. These will be the straps that will have the O-rings attached.
  • Step 11: Sewing O rings Thread a shorter length of 1 inch webbing through 2 O-rings. Fold webbing over about 6 inches and sew together using a straight stitch. Try to sew as close to the O-ring as possible. Reinforce stitching by sewing webbing forward and reverse 4-5 times. Reinforce webbing a few inches down as well. Repeat on other 3 ends.
  • Step 12: Threading O ring straps Thread your O-ring straps through the looped ends of your seat. The author alternated the straps through the supports.
  • Step 13: Threading longer straps Thread you longer double strap through the looped ends. Repeat with other strap.
  • Step 14: Reinforce ends and close loops Reinforce the ends and close the loops using a straight stitch. Be sure to ensure that you have an equal amount of strapping on each side.
  • Step 15: Attaching to walker Slide D-ring onto electrical clamp. Attach the plastic coated clamps and D-ring to the walker using a pair of pliers and a flat headed screwdriver. Be sure to tighten it so that it will not slip or slide. Thread double straps through D ring. Loop around and come back to O-rings. Thread strap through O-rings. Loop back around and thread through 1 O-ring. This should lock straps in place. Adjust as needed. Author: by nneul

Available

Price Check
Price: 
0.00
as of: 
07/15/2015
Additional Pricing Notes: 
Cost of materials
Seller(s): 
DIY Seat for a walker